Edge metal
Walls, curbs, pipes and edges are flashed for a finished roof.
Flat Roofing
Rubber Roof Installation Haledon, NJ
Installing a rubber roof in Haledon means choosing the EPDM thickness and attachment method, then flashing walls, curbs and edges so the membrane can move without tearing, with as few seams as possible. One call to (862) 434-1263 reaches a nearby rubber roof installer.
A true rubber roof is EPDM, a synthetic rubber membrane used on flat and low slope roofs for decades. The membrane is thick, stretchy rubber that tolerates temperature swings and resists hail and sunlight well. Unlike TPO and PVC, its seams are taped rather than heat welded.
EPDM can be attached in three main ways. Fully adhered roofs bond the whole sheet to the cover board with adhesive, mechanically attached roofs use plates and fasteners along the seams and ballasted roofs hold a loose sheet down with river stone. Residential roofs are most often fully adhered.
Thickness and color are the next choices. Thicker 60 mil membrane stands up better to foot traffic and hail. Black EPDM absorbs heat, which helps in cold climates, while white EPDM reflects sun and keeps rooms below cooler. Where the rubber meets a shingled roof or the house wall, the tie-in detail matters as much as any of these choices.
Many rubber roof installation calls in Haledon also turn up a need for rubber roof repair or flat roof installation.
Dealing with this in Haledon, NJ right now? Call (862) 434-1263 and describe the problem to a roofer who works in Haledon.
Call nowThe process
How rubber roof installation works
Each layer is set up to give the membrane a smooth, solid base.
Prepare the deck
The roofer checks the deck for rot, gaps and loose sheets and confirms the roof has enough slope to drain. Old roofing is removed if the roof is being replaced.
Add the cover board
Rigid insulation, often polyiso, is fastened with plates and screws, then a cover board goes on top. Low spots can be corrected with tapered insulation.
Sheet layout
Wide sheets are laid out to cover the roof with as few seams as possible, then allowed to relax. Laps are arranged so water flows over them.
Bond the membrane
Bonding adhesive is rolled onto both the cover board and the underside of the rubber, then the sheet is folded back down and broomed smooth. Each half gets the same treatment in turn. Brooming from the middle outward pushes trapped air to the edges.
Tape the laps
Laps are primed and joined with seam tape, then rolled to remove air. Lap sealant goes along exposed tape edges.
Flashing
Perimeter edge metal, wall flashing and pipe boots complete the roof. The top edge is sealed and covered. A final walk checks every seam with a probe before the job is closed out.
What is included
What rubber roof installation covers
Deck preparation
Old roofing is removed and the deck is repaired for a sound start.
Seams
Laps are joined with seam tape and is checked before closeout.
EPDM membrane
Wide sheets of EPDM cover the roof over a clean, dry base.
Cover board
Rigid insulation and a cover board form the base and gives the adhesive a firm grip.
Related service
EPDM Roof Installation Haledon, NJ
EPDM roof installation is straightforward in concept and demanding in the details. A flat, dry base, properly timed adhesive and carefully primed seams are what make EPDM last. Dry, mild days give the best bond. Different adhesives may be used in the field and at the flashings, each matched to the job it does.
In Haledon, an experienced EPDM installer leaves room for the membrane to move and age. Perimeter securement and proper flashing help prevent the shrinkage problems older rubber roofs show. Ask how the roofer secures the perimeter.
Local help
Rubber Roof Installation Near Me
In Haledon, EPDM is a popular choice for low slope roofs on additions and attached garages. Across Haledon and nearby towns like Paterson, Hawthorne, Totowa and Glen Rock, EPDM handles storms, sun and cold well when it is installed with good seams and drainage, so installation details matter as much as the material.
For rubber roof installation in Haledon, NJ or nearby towns like Paterson, Hawthorne, Totowa and Glen Rock, call (862) 434-1263 to reach a roofer who covers your street.
What the local climate does to a roof
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, building ice dams that push water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. Most homeowners in Haledon, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why fix it now
Less damage
Small roof problems caught early usually stay small repairs.
Roofers who know Haledon
Roofers in Haledon know the roof types and weather wear common in local homes.
Know what happens next
Ask the roofer about the cause, the options and the estimate before work starts.
Rubber Roof Installation questions
How long does a new rubber roof last?
A properly installed EPDM roof commonly lasts 20 to 30 years or more. Thickness, seam quality and maintenance all affect its life. Repairs are simple when needed.
What color EPDM is best?
Black and white each have their place. Black holds heat and white reflects it. Talk through the choice with a roofer.
Can a rubber roof go over an existing roof?
EPDM can sometimes go over an existing roof. There should be only one existing layer, the insulation must be dry and a cover board or recover board goes between the old roof and the rubber. Otherwise, a tear-off is needed. Core samples or a moisture scan show whether the old roof is dry enough.
How thick should a rubber roof be?
EPDM usually comes in 45 or 60 mil for homes. Sixty mil resists punctures better and lasts longer, which helps on roofs with foot traffic or hail. Even thicker sheets are available for demanding roofs.
What is the difference between EPDM and TPO?
EPDM is synthetic rubber, while TPO is a thermoplastic membrane. EPDM uses taped seams and stays flexible in cold, and TPO uses welded seams and reflects heat. Both are common on flat roofs.
More questions? Call (862) 434-1263
Often needed together
Rubber Roof Repair
Repairs for leaking rubber roofs, from peeling seams to pulled flashing at walls and curbs, never with tar or asphalt cement that ruins the rubber.
Learn moreFlat Roof Installation
Installing TPO, PVC, EPDM or modified bitumen roofs on additions, garages, porches and flat-roof homes, planned around how the roof will be used.
Learn moreTPO Roofing
Heat-welded TPO membrane for flat and low-slope roofs, with seams welded into one watertight sheet.
Learn moreFlat Roof Replacement
Full replacement of failing flat roofs, with a moisture survey deciding tear-off or recover, and new flashing at every wall, curb and drain.
Learn more
Looking for something else?
See all roofing servicesNeed rubber roof installation in Haledon, NJ?
Call (862) 434-1263 for a local roofer in Haledon and nearby towns.